This documentation page applies to the legacy Things Network Stack V2. Documentation for The Things Stack V3 is available here

Configuring the RAK811 WisNode LoRa Module

You can configure your WisNode by sending AT Commands via a Serial port tool running on your PC.The list below shows the AT Commands available for use:

AT Command Description
at+help This AT command can show all available AT commands of this module/product for you
at+version Get the current firmware version number.
at+get_config=device:status Get all information about the device’s hardware components and their current status.
at+set_config=device:restart After set, the device will restart.
at+set_config=device:boot Let the device work in boot mode
at+run Stop boot mode and run as normal. It is valid when the device works in boot mode.
at+set_config=device:sleep:X Get all information about the device’s hardware components and their current status.
at+set_config=device:gpio:X:Y Set a certain GPIO pin to high/low level.
X definition: the pin number of a certain GPIO on RAK811 module.
Y definition: 0: low level, 1: high level.
at+get_config=device:gpio:X Get a certain GPIO’s level.
X definition: the pin number of the GPIO on RAK811 module.
at+get_config=device:adc:X Get the ADC value.
X definition: the pin number of the ADC on RAK811 module.
at+set_config=device:iic:X:YY:ZZ:AAA Read data from I2C or write a data to I2C.
X definition: 0: read, 1: write.
YY definition: device address, in HEX format.
ZZ definition: sensor’s register address, in HEX format.
AAA definition: if read, this parameter means the length you want to read. If write, this parameter means the data you want to write. It must be in HEX format too.
at+set_config=device:uart_mode:X:Y Set the UART work mode.
X definition: UART number on RAK811 module.
Y definition: 0: Configuration mode; 1: Passthrough mode.
at+send=uart:X:YYY Set a certain UART’s Baud rate.
X definition: the UART number.
Y definition: the Baud rate value.
at+set_config=device:uart:X:Y Send data through UART.
X definition: the UART number of RAK811 module.
YYY definition: the data you want to send through UART.
at+join Start to join LoRa network
at+send=lora:X:YYY Send a customized data.
X definition: LoRa port
YYY definition: the data which you want to send. The limited length is 50 Bytes, and the data must be in HEX format.
at+set_config=lora:work_mode:X Set the work mode for LoRa.
X definition: 0: LoRaWAN, 1: LoRaP2P, 2: Test Mode.
at+set_config=lora:join_mode:X Set the join mode for LoRaWAN.
X definition: 0: OTAA, 1: ABP
at+set_config=lora:class:X Set the class for LoRa.
X definition: 0: Class A, 1: Class B, 2: Class C
at+set_config=lora:region:XXX Set the region for LoRa.
XXX define: one of the following items: EU868 EU433, CN470, IN865, EU868, AU915, US915, KR920, AS923.
at+set_config=lora:confirm:X Set the type of messages which will be sent out through LoRa.
X definition: 0: unconfirm, 1: confirm
at+set_config=lora:dev_eui:XXXX Set the device EUI for OTAA.
XXXX definition: the device EUI.
at+set_config=lora:app_eui:XXXX Set the application EUI for OTAA.
XXXX definition: the application EUI.
at+set_config=lora:app_key:XXXX Set the application key for OTAA.
XXXX definition: the application key.
at+set_config=lora:dev_addr:XXXX Set the device address for ABP.
XXXX definition: the device address.
at+set_config=lora:apps_key:XXXX Set the application session key for ABP.
XXXX definition: the application session key.
at+set_config=lora:nwks_key:XXXX Set the network session key for ABP.
XXXX definition: the network session key.
at+set_config=lora:ch_mask:X:Y Set a certain channel on or off.
X definition: the channel number, and you can check which channel can be set before you set it.
Y definition: 0: off, 1: on
at+set_config=lora:adr:X Open or close the ADR function of LoRa Node.
X definition: 0: Close ADR; 1: Open ADR.
at+set_config=lora:dr:X Set the DR of LoRa Node.
X definition: the number of DR. Generally, the value of X can be 0~5. More details, please check the LoRaWAN 1.0.2 specification.
at+set_config=lora:tx_power:X Set the TX power level.
X definition: The level of TX power. If you want to know the relationship between TX power level and dbm, please have a look at LoRaWAN 1.0.2 region specification on this link.
at+get_config=lora:status Returns all of the current information of LoRa, except LoRa channel.
at+get_config=lora:channel It will return the state of all LoRa channels, then you can see which channel is closed and which channel is open very clearly
at+set_config=lorap2p:XXX:Y:Z:A:B: C Set the parameters for LoRa P2P mode. This AT command is valid when the work mode is ·LoRaP2P.
XXX definition: Frequency in Hz.
Y definition: Spreading factor, [6, 7, 8, 9, 10, 11, 12].
Z definition: Bandwidth, 0: 125 kHz, 1: 250 kHz, 2: 500kHz.
A definition: Coding Rate, 1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8.
B definition: Preamble Length, 5~65535.
C definition: Power in dbm, 5~20.
at+send=lorap2p:XXX Send data through LoRaP2P. This AT command is valid when it works in LoRaP2P mode.
XXX definition: the data in HEX.