# Multitech - TTN connection lost after some days

**URL:** <https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017>\
**Category:** MultiTech Gateways\
**Created:** [March 2, 2018, 2:22pm UTC](https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017 "2018-03-02T14:22:03Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![trmax](https://www.thethingsnetwork.org/forum/user_avatar/www.thethingsnetwork.org/trmax/32/25844_2.png) [@trmax](https://www.thethingsnetwork.org/forum/u/trmax)\
**Post date:** [March 2, 2018, 2:22pm UTC](https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017/1 "2018-03-02T14:22:03Z")

</div>

hi

My configuration is:

Multitech Conduit (MTCDT-LEU1-247A) with loracard (MTAC-LORA-H-868) and GSM Cellular for WAN Transport.

After a few days of trouble-free operation, the gateway no longer sends data. after a restart, everyone is back.  
I looked at the log files and found the following:

> 14:43:08 INFO: Watchdog is disabled  
> 14:43:08 INFO: Contact email configured to “[xxx.xxx.com](http://xxx.xxx.com)”  
> 14:43:08 INFO: Description configured to “Gateway from IBBD.AT”  
> 14:43:08 INFO: [Transports] Initializing protocol for 1 servers  
> 14:43:09 INFO: [TTN] server “bridge.eu.thethings.network” connected  
> 14:43:09 INFO: [main] Starting the concentrator  
> ERROR: FAIL TO CONNECT BOARD  
> INFO: FPGA supported features: [TX filter] [Spectral Scan]  
> 14:43:09 ERROR: [main] failed to start the concentrator  
> 14:43:13 \*\*\* Multi Protocol Packet Forwarder for Lora Gateway \*\*\*  
> Version: 3.0.10  
> 14:43:13 \*\*\* Lora concentrator HAL library version info \*\*\*  
> Version: 5.0.1; Options: native;
> 
> * * *

devicehq is not interrupted. Only the last seen status on [console.thethingsnetwork.org](http://console.thethingsnetwork.org) is interrupted and and packages are not received.

markus

---

<div class="post-metadata">

**Author:** ![jreiss](https://www.thethingsnetwork.org/forum/user_avatar/www.thethingsnetwork.org/jreiss/32/46529_2.png) [@jreiss](https://www.thethingsnetwork.org/forum/u/jreiss)\
**Post date:** [March 2, 2018, 4:28pm UTC](https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017/2 "2018-03-02T16:28:17Z")

</div>

The log has this message but the unit is working after reboot?

Take note of the IP address on PPP  
$ ifconfig

When the device fails check again if the IP address has changed on the cellular interface.

Try to add “autoquit\_threshold” to the gateway config to restart if the IP changes.

Check that there is only one packet forwarder process running  
$ ps -A

Try to stop the packet forwarder, reset the lora card, then start the packet forwarder. This should occur on reboot  
$ mts-io-sysfs store lora/reset 0  
$ mts-io-sysfs store lora/reset 1

Check that the card hardware is functioning, cdone should go low when creset is low.  
$ mts-io-sysfs show lora/cdone  
$ mts-io-sysfs store lora/creset 0  
$ mts-io-sysfs show lora/cdone  
$ mts-io-sysfs store lora/creset 1  
$ mts-io-sysfs show lora/cdone

---

<div class="post-metadata">

**Author:** ![kersing](https://www.thethingsnetwork.org/forum/user_avatar/www.thethingsnetwork.org/kersing/32/44777_2.png) [@kersing](https://www.thethingsnetwork.org/forum/u/kersing)\
**Post date:** [March 2, 2018, 5:38pm UTC](https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017/3 "2018-03-02T17:38:00Z")

</div>

Please update to the newest version of the packet forwarder. To do so, get the newest installer from [https://github.com/kersing/multitech-installer](https://github.com/kersing/multitech-installer). Easiest way is log on to the conduit and run:

```auto
wget -O installer.sh https://raw.githubusercontent.com/kersing/multitech-installer/master/installer.sh
```

then re-run the installer with

```auto
sh installer.sh
```

---

<div class="post-metadata">

**Author:** ![sa\_catapult](https://www.thethingsnetwork.org/forum/user_avatar/www.thethingsnetwork.org/sa_catapult/32/14501_2.png) [@sa\_catapult](https://www.thethingsnetwork.org/forum/u/sa_catapult)\
**Post date:** [June 25, 2018, 10:47am UTC](https://www.thethingsnetwork.org/forum/t/multitech-ttn-connection-lost-after-some-days/13017/4 "2018-06-25T10:47:22Z")

</div>

Report. Same had happened to me; what I did (checking after every step if it works):

- reboot
- checked hw reset lines using commands mentioned above
- updated installer using commands mentioned above
- reflash FPGA hex with mts-fpga-loader to version v31 - success
- reflash FPGA hex with mts-fpga-loader to version v33 - fail
- reflash FPGA hex with mts-fpga-loader to version v31 - success
- reboot  
Works. So it might be updating installer, but with restart being required… which doesn’t make sense, or does it…?
