# Wifi config on a Multitech mLinux Conduit

**URL:** <https://www.thethingsnetwork.org/forum/t/wifi-config-on-a-multitech-mlinux-conduit/1244>\
**Category:** MultiTech Gateways\
**Created:** [February 13, 2016, 2:03pm UTC](https://www.thethingsnetwork.org/forum/t/wifi-config-on-a-multitech-mlinux-conduit/1244 "2016-02-13T14:03:32Z")\
**Posts on this page:** 1\
**Showing post:** 6

<div class="post-metadata">

**Author:** ![markstanley](https://www.thethingsnetwork.org/forum/user_avatar/www.thethingsnetwork.org/markstanley/32/301_2.png) [@markstanley](https://www.thethingsnetwork.org/forum/u/markstanley)\
**Post date:** [February 14, 2016, 11:55am UTC](https://www.thethingsnetwork.org/forum/t/wifi-config-on-a-multitech-mlinux-conduit/1244/6 "2016-02-14T11:55:25Z")

</div>

@kersing

Hi Jac,  
I followed your instructions to load the modules. I got no error messages so I presume they loaded ok. ifconfig -a shows:

> eth0 Link encap:Ethernet HWaddr 00:08:00:4A:06:33  
> inet addr:192.168.1.51 Bcast:192.168.1.255 Mask:255.255.255.0  
> UP BROADCAST MULTICAST MTU:1500 Metric:1  
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0  
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0  
> collisions:0 txqueuelen:1000  
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)  
> Interrupt:23 Base address:0xc000

> gre0 Link encap:UNSPEC HWaddr 00-00-00-00-FF-00-00-00-00-00-00-00-00-00-00-00  
> NOARP MTU:1476 Metric:1  
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0  
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0  
> collisions:0 txqueuelen:0  
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

> gretap0 Link encap:Ethernet HWaddr 00:00:00:00:00:00  
> BROADCAST MULTICAST MTU:1462 Metric:1  
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0  
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0  
> collisions:0 txqueuelen:1000  
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

> lo Link encap:Local Loopback  
> inet addr:127.0.0.1 Mask:255.0.0.0  
> UP LOOPBACK RUNNING MTU:65536 Metric:1  
> RX packets:187 errors:0 dropped:0 overruns:0 frame:0  
> TX packets:187 errors:0 dropped:0 overruns:0 carrier:0  
> collisions:0 txqueuelen:0  
> RX bytes:22230 (21.7 KiB) TX bytes:22230 (21.7 KiB)

> tunl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
> NOARP MTU:1480 Metric:1  
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0  
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0  
> collisions:0 txqueuelen:0  
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

…I presume I should expect to see wlan0 in the ifconfig if it was working?

Is there a list of compatible wifi adapters for the Conduits? I couldn’t find one on the Multitech site.

---

_[View the full topic](https://www.thethingsnetwork.org/forum/t/wifi-config-on-a-multitech-mlinux-conduit/1244)._