Additionally the output of dmesg is as below:-
root@mtcdt:~# dmesg
0x000000160000-0x000000200000 : "u-Boot Redundant Config"
0x000000200000-0x000000800000 : "uImage"
0x000000800000-0x000001000000 : "Config"
0x000001000000-0x000001800000 : "OEM Config"
0x000001800000-0x000010000000 : "Rootfs"
libphy: MACB_mii_bus: probed
macb f802c000.ethernet eth0: Cadence MACB at 0xf802c000 irq 23 (00:08:00:4a:37:2b)
macb f802c000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=f802c000.etherne:00, irq=-1)
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-atmel: EHCI Atmel driver
atmel-ehci 700000.ehci: EHCI Host Controller
atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
atmel-ehci 700000.ehci: irq 31, io mem 0x00700000
atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.12.27r15 ehci_hcd
usb usb1: SerialNumber: 700000.ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci 600000.ohci: AT91 OHCI
at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
at91_ohci 600000.ohci: irq 31, io mem 0x00600000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: AT91 OHCI
usb usb2: Manufacturer: Linux 3.12.27r15 ohci_hcd
usb usb2: SerialNumber: at91
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
rtc (null): invalid alarm value: 1900-1-1 0:0:0
at91_rtc fffffeb0.rtc: rtc core: registered fffffeb0.rtc as rtc0
at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
i2c /dev entries driver
at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=0)
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3964 buckets, 15856 max)
ipip: IPv4 over IPv4 tunneling driver
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
IPv4 over IPSec tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
mip6: Mobile IPv6
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
l2tp_core: L2TP core driver, V2.0
Key type dns_resolver registered
at91_rtc fffffeb0.rtc: setting system clock to 2018-03-24 10:47:25 UTC (1521888445)
usb 2-3: new full-speed USB device number 2 using at91_ohci
usb 2-3: New USB device found, idVendor=04e2, idProduct=1414
usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
VFS: Mounted root (jffs2 filesystem) readonly on device 31:8.
devtmpfs: mounted
Freeing unused kernel memory: 168K (c0574000 - c059e000)
jffs2: notice: (74) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
jffs2: notice: (74) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
udevd[85]: starting version 182
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
pps pps0: new PPS source pps.7.-1
pps pps0: Registered IRQ 32 as PPS source
tmp102 0-0048: initialized
atmel_usba_udc 500000.gadget: MMIO registers at 0xf803c000 mapped at d0928000
atmel_usba_udc 500000.gadget: FIFO at 0x00500000 mapped at e1100000
atmel_spi f0000000.spi: version: 0x212
atmel_spi f0000000.spi: Using dma0chan1 (tx) and dma0chan2 (rx) for DMA transfers
atmel_spi f0000000.spi: Atmel SPI Controller at 0xf0000000 (irq 28)
atmel_spi f0000000.spi: master is unqueued, this is deprecated
atmel_spi f0004000.spi: version: 0x212
atmel_spi f0004000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
atmel_spi f0004000.spi: Atmel SPI Controller at 0xf0004000 (irq 29)
atmel_spi f0004000.spi: master is unqueued, this is deprecated
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
vizzini 2-3:1.0: This device cannot do calls on its own. It is not a modem.
vizzini 2-3:1.0: ttyXRUSB0: XR21v14x usb uart device
vizzini 2-3:1.2: This device cannot do calls on its own. It is not a modem.
vizzini 2-3:1.2: ttyXRUSB1: XR21v14x usb uart device
vizzini 2-3:1.4: This device cannot do calls on its own. It is not a modem.
vizzini 2-3:1.4: ttyXRUSB2: XR21v14x usb uart device
atmel_mci f0008000.mmc: version: 0x504
vizzini 2-3:1.6: This device cannot do calls on its own. It is not a modem.
atmel_mci f0008000.mmc: using dma0chan3 for DMA transfers
vizzini 2-3:1.6: ttyXRUSB3: XR21v14x usb uart device
atmel_mci f0008000.mmc: Atmel MCI controller at 0xf0008000 irq 22, 1 slots
usbcore: registered new interface driver vizzini
vizzini: Exar USB UART Driver for XR21V141x
[INFO] mts-io:mts_io_init:1007: init: v1.5.16
[INFO] mts-io:mts_id_eeprom_load:913: detected board MTCDT-0.1
[INFO] mts-io:mts_id_eeprom_load:921: sizeof: 512
[INFO] mts-io:mts_id_eeprom_load:922: vendor-id: Multi-Tech Systems
[INFO] mts-io:mts_id_eeprom_load:923: product-id: MTCDT-247A
[INFO] mts-io:mts_id_eeprom_load:924: device-id: 19528911
[INFO] mts-io:mts_id_eeprom_load:925: hw-version: MTCDT-0.1
[INFO] mts-io:mts_id_eeprom_load:932: mac-addr: 00:08:00:4A:37:2B
[INFO] mts-io:mts_id_eeprom_load:934: imei:
[INFO] mts-io:mts_id_eeprom_load:935: capa-gps: yes
[INFO] mts-io:mts_id_eeprom_load:936: capa-din: no
[INFO] mts-io:mts_id_eeprom_load:937: capa-dout: no
[INFO] mts-io:mts_id_eeprom_load:938: capa-adc: no
[INFO] mts-io:mts_id_eeprom_load:939: capa-wifi: yes
[INFO] mts-io:mts_id_eeprom_load:940: capa-bluetooth: yes
[INFO] mts-io:mts_id_eeprom_load:941: capa-lora: no
[INFO] mts-io:mts_id_eeprom_load:950: mac-bluetooth: 00:23:A7:C9:04:44
[INFO] mts-io:mts_id_eeprom_load:959: mac-wifi: 00:23:A7:CA:F8:30
[INFO] mts-io:mts_id_eeprom_load:966: uuid: 75EC47543675B8DB355002EA1CE14367
[INFO] mts-io:load_port:694: no accessory card inserted in port 1
[INFO] mts-io:load_port:729: accessory card 2 vendor-id: Multi-Tech Systems
[INFO] mts-io:load_port:730: accessory card 2 product-id: MTAC-LORA-H-868
[INFO] mts-io:load_port:731: accessory card 2 device-id: 19525146
[INFO] mts-io:load_port:732: accessory card 2 hw-version: MTAC-LORA-1.5
[INFO] mts-io:load_port:753: accessory card 2 eui: 00:80:00:00:A0:00:1F:D5
[INFO] mts-io:lora_setup:60: loading LORA accessory card in port 2
[INFO] mts-io:lora_setup:90: created link [lora] to [ap2], success:0
[INFO] mts-io:lora_setup:125: Substitute pins
[INFO] mts-io:lora_setup:131: LORA H: Replace name AP2_GPIO1 with name AP2_CDONE
[INFO] mts-io:lora_setup:132: LORA H: Replace pin number 84 with number 84
[INFO] mts-io:lora_setup:131: LORA H: Replace name AP2_GPIO2 with name AP2_CRESET
[INFO] mts-io:lora_setup:132: LORA H: Replace pin number 85 with number 85
[INFO] mts-io:lora_setup:189: ap_subdirs[port_index=1] = cf0c8b20 ap_subdirs[port_index=1]=bf0d6958
usb 1-2: new high-speed USB device number 2 using atmel-ehci
usb 1-2: New USB device found, idVendor=0424, idProduct=2534
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.1: new high-speed USB device number 3 using atmel-ehci
[INFO] mts-io:mts_attr_store_radio_reset:289: radio is reset
usb 1-2.1: New USB device found, idVendor=0424, idProduct=2534
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-2.1:1.0: USB hub found
hub 1-2.1:1.0: 4 ports detected
usb 1-2.2: new high-speed USB device number 4 using atmel-ehci
usb 1-2.2: New USB device found, idVendor=1618, idProduct=9113
usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
usb 1-2.2: Product: Wireless USB Network Module
usb 1-2.2: Manufacturer: Redpine Signals, Inc.
usb 1-2.2: SerialNumber: 000000000001
usb 1-2: USB disconnect, device number 2
usb 1-2.1: USB disconnect, device number 3
usb 1-2.2: USB disconnect, device number 4
usb 1-2: new high-speed USB device number 5 using atmel-ehci
usb 1-2: New USB device found, idVendor=0424, idProduct=2534
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.1: new high-speed USB device number 6 using atmel-ehci
usb 1-2.1: New USB device found, idVendor=0424, idProduct=2534
usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-2.1:1.0: USB hub found
hub 1-2.1:1.0: 4 ports detected
usb 1-2.2: new high-speed USB device number 7 using atmel-ehci
usb 1-2.2: New USB device found, idVendor=1618, idProduct=9113
usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
usb 1-2.2: Product: Wireless USB Network Module
usb 1-2.2: Manufacturer: Redpine Signals, Inc.
usb 1-2.2: SerialNumber: 000000000001
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb f802c000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
g_serial gadget: Gadget Serial v2.4
g_serial gadget: g_serial ready
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode